High Gloss Chemical Resistant Novolac Based Epoxy White / Clear – Corro Guard
Corro Guard (formerly known as Steel Plus CE) is water-based, 100% Novolac based epoxy available in clear and white finishes. Steel Plus CE Epoxy is chemical and corrosion resistance with a low odor ideal for commercial applications where workers are present without causing downtime. Corro Guard Epoxy is an accepted USDA and FDA epoxy product.
Corro Guard™ White and Clear are very high quality, water-based epoxy paints that are cured with an aliphatic amine curing agent for the utmost in chemical and corrosion resistance. The clear is designed to be used over Steel Plus CE-316 to offer an additional coat of high gloss protection or to be used alone as a clear finish. The white is used in place of the stainless steel finish where USDA White is required.
These high gloss enamels are two-component, water-based, 100% Novolac based epoxies. They contain no HAP solvents, have exceptionally fast dry and are cured with a cycloaliphatic amine curing agent. They are a 2 to 1 mix that requires no induction time and has the exceptional chemical and corrosion resistance expected from a Novolac epoxy. Their low odor makes them ideal to use in a warehouse or manufacturing plant while workers are present. They are very low VOC, are easy to apply, with water clean up and are USDA and FDA accepted.
Uses for Corro Guard™: Epoxy A tough, heavy-duty, extremely chemical resistant epoxy designed for maximum performance in severe environments.
Available Appearances: High Gloss Clear and High Gloss White
Required Curing Agent: 16-CURE; mixing ratio (2) parts “A” + (1) part “B” by volume
Recommended Primers: In most cases, Steel Plus CE is used over a stainless steel middle-coat. Steel Plus Epoxy Primer or Prime Solution 5250 Red/5253 Gray.
Surface Preparation for Chemical Resistant Epoxy Paints:
Required on all metal or old coatings: Remove all dirt, grease, oil, salt, and chemical contaminants by washing the surface with BC-4000 cleaner or another suitable cleaner. Thoroughly cured old coatings or new smooth metal may require scuff sanding for maximum adhesion.
Moderate Exposure: Abrasive blast the surface to SSPC-SP-6 commercial blast before priming.
Severe Exposure: Abrasive blast the surface to SSPC-SP-10 near white blast before priming.
How to Apply Chemical and Corrosion resistant Epoxy Paints:
Apply only when air and surface temperatures are between 50oF and 100oF and surface temperature is at least 5oF above the dew point.
Thinning Epoxy Corro Guard™ Coating:
Using Roller or a Brush: Use as mixed. Dilute with water as needed.
Using an Air Atomized Sprayer: Dilute up to 5-10% with water if needed.
Using an Airless Sprayer: Normally, no dilution needed.
Steel Plus CE Clean Up: Use soap and water
Recommended Equipment to Use when Applying Corro Guard™ High Gloss Epoxy:
Filter: Use 100 mesh stainless steel screen or nylon bag when needed
Brush: Use a quality synthetic bristle brush
Roller: Use quality roller cover
Air Atomized Sprayer: Please follow the equipment manufacturers nozzle and needle selection recommendation for use with medium viscosity paints. Spray at 45-60 psi.
Airless Sprayer: 1800-2400 psi with 0.011-0.013 tip
Hot Spraying Temperature: 120oF
Specifications of CORRO GUARD Novolac Based Epoxy:
Weight Per Gallon: 8.70 Lbs
Solids by Weight: 26.51%
Solids by Volume: 23.52% (part “A” alone), 30.98% (part “A” & “B” combined)
Recommended DFT: 2.5 mils.
WFT to Achieve DFT: 8.0 mils.
Induction Time: None
Theoretical Coverage: @1 MIL DFT 495 sq. ft./gal
Actual Coverage ar recommended DFT: 198 sq. ft./gal
Dry Time @77F and50% Humidity: Tack Free: 20-60 minutes
Handle: 2-4 hour
Recoat: 1 hour after dry to touch
Full Cure: 7 days (drying can be accelerated)
Pot Life: 2 hours (mix just enough paint to use up in 2 hours)
Heat Resistant when fully cured: 300F
Shelf Life: 1 year
Important Safety Information for Corro Guard™ High Gloss Novolac Based Epoxy
VOC: 188 g/L, or 1.57 Lbs/gal (part “A” & “B” combined)
Flash Point: N/A
Warning: California Prop. 65 warning: Detectable amounts of chemicals known to the state of California to cause cancer, birth defects or other reproductive harm, may be found in this product or its vapors. For specific information refer to the Safety Data Sheet(SDS).
*** FOR INDUSTRIAL USE ONLY. KEEP OUT OF REACH OF CHILDREN. ***
Novolac Based Epoxy White and Clear Corro Guard™ Ordering Information:
Corro Guard™ (Clear)
Product Number | Size | Wt./Case | Case Quantity |
20-450A-F4 | 1 Quart | 16 | 6 |
20-450A-F1 | 1 Gallon | 36 | 4 |
20-450A-F5 | 5 Gallons | 48 | 1 |
Corro Guard™ (White)
Product Number | Size | Wt./Case | Case Quantity |
20-809A-F4 | 1 Quart | 14 | 6 |
20-809-F1 | 1 Gallon | 36 | 4 |
20-809A-F5 | 5 Gallons | 48 | 1 |
Please Note: This product needs a curing agent. If you order 1 Gallon you will need Qty. 2 16-Cure-F4 (Quart), If you order 5-Gallon pail you will need Qty. 2 16-Cure-F1 (Gallon) and Qty. 2 16-Cure-F4 (Quart) and if you order Quart you will need Qty. 2 16-Cure-8 (1/2 Pint).
WEIGHT PER GALLON 8.70 Lbs
SOLIDS BY WEIGHT 26.51%
SOLIDS BY VOLUME 23.52% (part “A” alone), 30.98% (part “A” & “B” combined)
RECOMMENDED DFT 2.5 mils
WFT TO ACHIEVE DFT 8.0 mils
INDUCTION TIME None
THEORETICAL COVERAGE @1 MIL DFT 495 sq. ft./gal
ACTUAL COVERAGE AT RECOMMENDED DFT 198 sq. ft./gal
DRY TIME @77OF
AND 50% HUMIDITY Tack Free: 20-60 minutes
Handle: 2-4 hour
Recoat: 1 hour after dry to touch
Full Cure: 7 days (drying can be accelerated)
POT-LIFE 2 hours (mix just enough paint to use up in 2 hours)
HEAT RESISTANCE
OF CURED FILM 300oF
SHELF-LIFE 1 year
Additional information
Size | 1 Quart, 1 Gallon, 5 Gallons |
---|---|
Color | Clear, White |
Corro Guard White and Clear (formally know as Steel Plus CE) is a high quality, water-based epoxy paints that are cured with an aliphatic amine curing agent for the utmost in chemical and corrosion resistance. The clear is designed to be used over Corro Guard-316 to offer an additional coat of high gloss protection or to be used alone as a clear finish. The white is used in place of the stainless steel finish where USDA White is required.
These high gloss enamels are two-component, water-based, 100% Novolac based epoxies. They contain no HAP solvents, have exceptionally fast dry and are cured with a cycloaliphatic amine curing agent. They are a 2 to 1 mix that requires no induction time and has the exceptional chemical and corrosion resistance expected from a Novolac epoxy. Their low odor makes them ideal to use in a warehouse or manufacturing plant while workers are present. They are very low VOC, are easy to apply, with water clean up and are USDA and FDA accepted.
Uses for Corro Guard: Epoxy A tough, heavy-duty, extremely chemical resistant epoxy designed for maximum performance in severe environments.
Available Appearances: High Gloss Clear and High Gloss White
Required Curing Agent: 16-CURE; mixing ratio (2) parts “A” + (1) part “B” by volume
Recommended Primers: In most cases, Corro Guard is used over a stainless steel middle-coat. Corro Guard Epoxy Primer or Prime Solution 5250 Red/5253 Gray.
Surface Preparation for Chemical Resistant Epoxy Paints:
Required on all metal or old coatings: Remove all dirt, grease, oil, salt, and chemical contaminants by washing the surface with BC-4000 cleaner or another suitable cleaner. Thoroughly cured old coatings or new smooth metal may require scuff sanding for maximum adhesion.
Moderate Exposure: Abrasive blast the surface to SSPC-SP-6 commercial blast before priming.
Severe Exposure: Abrasive blast the surface to SSPC-SP-10 near white blast before priming.
How to Apply Chemical and Corrosion resistant Epoxy Paints:
Apply only when air and surface temperatures are between 50oF and 100oF and surface temperature is at least 5oF above the dew point.
Thinning Epoxy Corro Guard Coating:
Using Roller or a Brush: Use as mixed. Dilute with water as needed.
Using an Air Atomized Sprayer: Dilute up to 5-10% with water if needed.
Using an Airless Sprayer: Normally, no dilution needed.
Corro Guard Clean Up: Use soap and water
Recommended Equipment to Use when Applying Corro Guard High Gloss Epoxy:
Filter: Use 100 mesh stainless steel screen or nylon bag when needed
Brush: Use a quality synthetic bristle brush
Roller: Use quality roller cover
Air Atomized Sprayer: Please follow the equipment manufacturers nozzle and needle selection recommendation for use with medium viscosity paints. Spray at 45-60 psi.
Airless Sprayer: 1800-2400 psi with 0.011-0.013 tip
Hot Spraying Temperature: 120oF
Specifications of Corro Guard Novolac Based Epoxy:
Weight Per Gallon: 8.70 Lbs
Solids by Weight: 26.51%
Solids by Volume: 23.52% (part “A” alone), 30.98% (part “A” & “B” combined)
Recommended DFT: 2.5 mils.
WFT to Achieve DFT: 8.0 mils.
Induction Time: None
Theoretical Coverage: @1 MIL DFT 495 sq. ft./gal
Actual Coverage ar recommended DFT: 198 sq. ft./gal
Dry Time @77F and50% Humidity: Tack Free: 20-60 minutes
Handle: 2-4 hour
Recoat: 1 hour after dry to touch
Full Cure: 7 days (drying can be accelerated)
Pot Life: 2 hours (mix just enough paint to use up in 2 hours)
Heat Resistant when fully cured: 300F
Shelf Life: 1 year
Important Safety Information for Corro Guard High Gloss Novolac Based Epoxy
VOC: 188 g/L, or 1.57 Lbs/gal (part “A” & “B” combined)
Flash Point: N/A
Warning: California Prop. 65 warning: Detectable amounts of chemicals known to the state of California to cause cancer, birth defects or other reproductive harm, may be found in this product or its vapors. For specific information refer to the Safety Data Sheet(SDS).
*** FOR INDUSTRIAL USE ONLY. KEEP OUT OF REACH OF CHILDREN. ***
Novolac Based Epoxy White and Clear Corro Guard Ordering Information:
Corro Guard (Clear)
Product Number | Size | Wt./Case | Case Quantity |
20-450A-F4 | 1 Quart | 16 | 6 |
20-450A-F1 | 1 Gallon | 36 | 4 |
20-450A-F5 | 5 Gallons | 48 | 1 |
Corro Guard (White)
Product Number | Size | Wt./Case | Case Quantity |
20-809A-F4 | 1 Quart | 14 | 6 |
20-809-F1 | 1 Gallon | 36 | 4 |
20-809A-F5 | 5 Gallons | 48 | 1 |
Please Note: This product needs a curing agent. If you order 1 Gallon you will need Qty. 2 16-Cure-F4 (Quart), If you order 5-Gallon pail you will need Qty. 2 16-Cure-F1 (Gallon) and Qty. 2 16-Cure-F4 (Quart) and if you order Quart you will need Qty. 2 16-Cure-8 (1/2 Pint).