Clear Gloss Antimicrobial Topcoat – Resist 650 Strains of Bacteria Silver Bullet AM™

A clear, non-yellowing, high gloss coating that contains an antimicrobial agent that is effective against a broad spectrum of bacteria as well as mold, mildew, and algae. Silver Bullet AM uses low VOC, acrylic technology to provide a protective topcoat for hard surfaces.

Get Local Price Information Now

Clear

Product Description

Silver Bullet AM™ is a clear, non-yellowing, high gloss coating that contains an antimicrobial agent that is effective against a broad spectrum of bacteria as well as mold, mildew, and algae. Silver Bullet AM uses low VOC, acrylic technology to provide a protective topcoat for hard surfaces.  Recommended Primers: CORRO GUARD PRIMER or PRIME LOCK.

Surface Preparation Silver Bullet AM Clear Gloss Antimicrobial Topcoat:

Required on all metal or old coatings: Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with BC-4000 cleaner or other suitable cleaners. Thoroughly cured old coatings or new smooth metal may require scuff sanding for maximum adhesion. Moderate Exposure: Abrasive blast the surface to SSPC-SP-6 commercial blast before priming. Severe Exposure: Abrasive blast the surface to SSPC-SP-10 near white blast before priming.

How to Apply Antimicrobial Clear Topcoat:

Apply only when air and surface temperatures are between 50°F and 100°F and surface temperature is at least 5°F above the dew point. Thinning: Using Roller or a Brush: Use as mixed.  Using an Air Atomized Sprayer: Normally not needed.  Using an Airless Sprayer: Normally not needed. Clean Up: Use isopropyl alcohol, xylene or acetone.

Recommended Equipment to Use when Applying Antimicrobial Clear Topcoat:

Filter: Use 50 mesh stainless steel screen or nylon bag when needed Brush: Use a quality synthetic bristle brush Roller: Use quality roller cover Air Atomized Sprayer: Please follow the equipment manufacturers nozzle and needle selection recommendation for use with medium viscosity paints. Spray at 45-60 psi. Airless Sprayer: 1800-2400 psi with 0.009-0.013. tip Hot Spraying Temperature: 120°F

Specifications of Silver Bullet AM Clear Gloss Antimicrobial Topcoat:

Weight Per Gallon: 8.89 Lbs Solids by Weight: 29% Solids by Volume: 27%  Recommended DFT: 1 mils. WFT to Achieve DFT: 4 mils. Induction Time: None Theoretical Coverage:  400 sq ft/gallon @ 1 mil DFT  Actual Coverage at recommended DFT: 400 sq ft/gallon  Dry Time @77°F  and 50% Humidity: Tack Free: 60 minutes Handle: 2-4 hour Recoat: 1 hour after dry to touch  Full Cure: 7 days (drying can be accelerated) Pot Life: N/A Heat Resistant when fully cured:  Not Tested  Shelf Life: 1 year

Important Safety Information for Antimicrobial Clear Topcoat:

VOC: 50 g/L or 0.417 Lbs/gal  Warning: California Prop. 65 warning: Detectable amounts of chemicals known to the state of California to cause cancer, birth defects or other reproductive harm, may be found in this product or its vapors. For specific information refer to the Safety Data Sheet(SDS).

*** FOR INDUSTRIAL USE ONLY. KEEP OUT OF REACH OF CHILDREN. ***


Silver Bullet AM™ Clear Gloss Antimicrobial Topcoat Ordering Information:


Product Number Size Wt./Case Case Quantity
11-451AM-F1 1 Gallon 36 4
11-451AM-F5 5 Gallons 48 1

 

Additional Information

Size

1 Gallon, 5 Gallons

Reviews

There are no reviews yet.

Be the first to review “Clear Gloss Antimicrobial Topcoat – Resist 650 Strains of Bacteria Silver Bullet AM™”

Your email address will not be published. Required fields are marked *