Gloss Stainless Steel Antimicrobial Epoxy Paint – Resist 650 Strains of Bacteria Silver Bullet AM 316™
Stainless Steel heavy-duty, extremely chemical resistant epoxy coating designed for maximum performance in severe environments. It contains silver and copper ions to protect against 650 strains of bacteria and a fungicide to protect against mold, mildew, and algae.
Silver Bullet AM-316 is a semi-gloss, stainless metallic finish that contains a broad spectrum antimicrobial agent that makes the surface of the coating effective against a broad spectrum of bacteria as well as mold, mildew, and algae. Silver Bullet AM uses our new technology water-based epoxy resins for maximum durability in demanding applications. Silver Bullet AM-316 is for interior applications only. VOC compliant. Silver Bullet AM® is available in Clear, Black, and White Required Curing Agent: 16-CURE; mixing ratio (2) parts “A” + (1) part “B” by volume Recommended Primers: Usually used over a stainless steel middle-coat. Steel Plus Epoxy Primer or Prime Solution 5250 Red/5253 Gray
Surface Preparation Silver Bullet AM Stainless Steel Antimicrobial Coating:
Required on all metal or old coatings: Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with BC-4000 cleaner or other suitable cleaners. Thoroughly cured old coatings or new smooth metal may require scuff sanding for maximum adhesion. Moderate Exposure: Abrasive blast the surface to SSPC-SP-6 commercial blast before priming. Severe Exposure: Abrasive blast the surface to SSPC-SP-10 near white blast before priming.
How to Apply Stainless Steel Antimicrobial Epoxy Paints:
Apply only when air and surface temperatures are between 50oF and 100oF and surface temperature is at least 5oF above the dew point. Thinning AM 316 Coating: Using Roller or a Brush: Use as mixed. Dilute with water as needed. Using an Air Atomized Sprayer: Dilute up to 5-10% with water if needed. Using an Airless Sprayer: Normally, no dilution needed. Steel Plus CE Clean Up: Use soap and water
Recommended Equipment to Use when Applying Stainless Steel Antimicrobial Epoxy:
Filter: Use 50 mesh stainless steel screen or nylon bag when needed Brush: Use a quality synthetic bristle brush Roller: Use quality roller cover Air Atomized Sprayer: Please follow the equipment manufacturers nozzle and needle selection recommendation for use with medium viscosity paints. Spray at 45-60 psi. Airless Sprayer: 1800-2400 psi with 0.013-0.015 tip Hot Spraying Temperature: 120F
Specifications of Silver Bullet Stainless Steel Antimicrobial Epoxy:
Weight Per Gallon: 9.67 Lbs Solids by Weight: 36.85% Solids by Volume: 26.16% (part “A” alone), 32.74% (part “A” & “B” combined) Recommended DFT: 2.5 mils. WFT to Achieve DFT: 7.5 mils. Induction Time: None Theoretical Coverage: @1 MIL DFT 524 sq. ft./gal Actual Coverage ar recommended DFT: 209 sq. ft./gal Dry Time @77F and50% Humidity: Tack Free: 20-60 minutes Handle: 2-4 hour Recoat: 1 hour after dry to touch Full Cure: 7 days (drying can be accelerated) Pot Life: 2 hours (mix just enough paint to use up in 2 hours) Heat Resistant when fully cured: 300F Shelf Life: 2-year
Important Safety Information for Antimicrobial 316 Epoxy Paint Coating:
VOC: 193 g/L or 1.6 Lbs/gal (part “A” & “B” combined) Flash Point: N/A Warning: California Prop. 65 warning: Detectable amounts of chemicals known to the state of California to cause cancer, birth defects or other reproductive harm, may be found in this product or its vapors. For specific information refer to the Safety Data Sheet(SDS).
*** FOR INDUSTRIAL USE ONLY. KEEP OUT OF REACH OF CHILDREN. ***
Silver Bullet AM 316™ Ordering Information:
|Product Number||Size||Wt./Case||Case Quantity|
Please Note: This product needs a curing agent. If you order 1 Gallon you will need Qty. 2 16-Cure-F4 (Quart), If you order 5-Gallon pail you will need Qty. 2 16-Cure-F1 (Gallon) and Qty. 2 16-Cure-F4 (Quart) and if you order Quart you will need Qty. 2 16-Cure-8 (1/2 Pint).
1 Quart, 1 Gallon, 5 Gallons
There are no reviews yet.